Final Analysis  
Property Inspection Report

" We see what's missing "

Final Analysis Property Inspections

1385 Fordham Dr. Ste. 105, Virginia Beach VA 23464

www.Final-Analysis.com

Prepared exclusively for

removed for privacy

xxx Cardover Ave.
Chesapeake VA 23325

Report ID: xxxx050916

 

 

Inspection Date: 5/9/2016

Inspector:

Reuben Autery

www.final-analysis.com

757.495.2300

Top Table of Contents Bottom

Table of Contents


Top Table of Contents Bottom
Date: 5/9/2016 Time: 09:00 AM Report ID: ragle050916
Property:
xxx Cardover Ave.
Chesapeake VA 23325
Customer:
removed for privacy
Real Estate Professional:
Sharon Milligan
All Pros Realty

Type of Inspection:
Home Buyers inspection

Inspection Procedures:
American Society of Home Inspectors, Standards of practice

Inspector:

Reuben Autery, DPOR 3380000742

Inspection Restrictions/limitations:
None

General inspection accessibility:
Occupied, furnished

All Utility services are on?:
Yes

In Attendance:
Buyer, Buyers Agent

Type of building:
Single Family (1 story)

Square Feet of conditioned space:
1508

Age of building (year built):
1973

# of Bedrooms:
3 Bedrooms

# of Bathrooms:
1.5 bathrooms

Temperature during inspection:
71

Weather:
Clear

Ground/Soil surface condition:
Dry

Garage:
1.5 car, detached

Comment Key or Definitions

The following definitions of comment descriptions represent this inspection report. All comments by the inspector should be considered before purchasing this home. Any recommendations by the inspector to repair or replace suggests a second opinion or further inspection by a qualified contractor. All costs associated with further inspection fees and repair or replacement of item, component or unit should be considered before you purchase the property.

Inspected (IN) = I visually observed the item, component or unit and if no other comments were made then it is satisfactory and appeared to be functioning as intended allowing for normal wear and tear.

Not Inspected (NI)= I did not inspect this item, component or unit and made no representations of whether or not it was functioning as intended and will state a reason for not inspecting.

Not Present (NP) = This item, component or unit does not exists in this home or building.

Information & Disclosures (ID) =   graphic    Indicated with an ORANGE flag and text. This is   Important information you should know about this house or building including, disclosures, alerts, advisories and warnings about typical conditions or circumstances for this home. Not necessarily something abnormal or unusual or in need of action, but none the less critical information that may pose significant concern for health risk, environmental safety or additional cost. These "orange flag" items will also be separately listed in the Information and Disclosure summary page of this report.

Repair or Replace (RR) = graphic Indicated with a RED Flag and text. Corrective action recommended. These items, systems, components or unit is not functioning as intended, defective, broken or otherwise needs further inspection and evaluation by a qualified contractor. Items, components or units that should be repaired, replaced or corrected or otherwise represent significant, unusual, abnormal cost or safety concerns.  These "red flag" items will also be separately listed in the DEFECT summary page of this report.

Inspection standards of practice: This inspection was completed in compliance with the professional standards of practice set forth by the  American Society of Home inspectors (ASHI) and VA Dept. of Professional Occupation and Regulation (DPOR) for Home Inspectors. These standards and regulations describe the scope, procedures and limitations of a standard home inspection and are provided for your review. Additionally the ASHI standards of practice are included in the appropriate header section of each corresponding system of the report.

Purpose and Objective: This inspection is not technically exhaustive and can not be conclusive of every detail.  The primary objective of this building inspection is to identify and report MATERIAL DEFECTS. Material Defects are defined as a specific issue with a system or component of a residential property that may have a significant, adverse impact on the value of the property, or that poses an unreasonable risk to people.  The fact that a system or component is near, at or beyond the end of its normal useful life is not, in itself, a material defect. Normal wear and tear, maintenance typical defects or deficiencies are not defined as material defects. That is not to say that the home inspector will not report smaller defects such as cracked glass, broken outlets or leaky faucet washers but this is not the primary objective of an inspection. The home inspection is a first look attempt at ascertaining the general condition of a property. While it is the purpose of this inspection to discover and disclose those major items and concerns that may have an adverse impact on the value of this property and the health and safety of it's occupants, it is not an exhaustive list of defects or discrepancies and it certainly should not be used as a punch list of repairs. Repair list and cost estimates should be obtained from contractors.  It is important to know that home inspectors are general practitioners with a limited amount of time and capabilities and are primarily focused on major issues in the home.  Outside of normal testing and observation, Inspectors do not engage in troubleshooting or diagnostics and can not offer repair advice.   Home inspections are limited to visual observations only and does not include technically exhaustive or invasive analysis. However, this report attempts to identify and recommend conditions that should have further evaluation by experts prior to closing or taking ownership.

Typically found on any home and  included in any inspection report will be smaller issues, discrepancies, observations and suggestions. These may not be considered serious or significant problems  but common to find on all homes and is mostly provided as courtesy in an attempt to give you a more comprehensive understanding of the home.  These smaller, typical or common discrepancies are not intended to be all inclusive.

It is the objective of the inspection and report to provide you the means by which you can progress in an informed manner thereby protecting yourself as much as possible before taking ownership of a property. This may mean obtaining further evaluation and repairs by an expert, purchase price adjustments, escrow of funds for repair, or withdrawing from a buyers purchase agreement altogether.  If you are subject to an inspection contingency removal purchase addendum your conditions and disposition of removing that contingency should be clearly stated with details of expected outcomes.  Furthermore, it should also be stated that any dispositions agreed to should be subjective to your re-inspection and final acceptance of satisfactory completion prior to closing of escrow.

Repairs -  No matter how big or small, All repairs, corrections or replacements should be requested to be completed by licensed, qualified professionals with copies of their credentials, licensing, labor and product warranties and receipts of work. It is not recommend that you ask the seller to make the repairs unless they are qualified in the trades and you feel confident that they'll do a good quality job. It should be expected and required that all work be accompanied by any required city permits and inspections. Mostly all work except minor repairs require city permits and inspections. Finally, all repairs should be subject to your re-inspection, satisfaction and approval a couple days before closing. If you are submitting a Property Inspection Contingency Removal Addendum with list of requested repairs (PICRA), you should consider adding the above verbiage to your PICRA because at that point you will be agreeing to buy the house subject to seller repairs and might need assurance they are done correctly.

Reinspection - Due to liability restrictions, reinspections are not the policy of Final Analysis home inspections. All repairs or corrections should be completed by qualified, licensed professional in their trade and should be accompanied by permits, work orders, receipts and warranties. If you feel a reinspection is necessary we can provide on a case by case basis and subject to schedule availability. The property inspection contingency removal addendum (PICRA) should be provided to us when the re-inspection is requested.   All re-inspections are subject to a minimum fee of $200 and will be accompanied by an updated report.

NOTICE OF URGENCY: If you are buying this property, any discrepancies, concerns or issues revealed in this report should be resolved to your satisfaction before close of escrow and/or taking possession.

NOTICE - A Termite and moisture inspection was not ordered or completed during this inspection by Final Analysis Property inspections LLC.  These are the specific inspections and reports required by some financial institutions to underwrite a mortgage.  Termite and Moisture inspections look for and report on the presence of wood damaging organisms. These inspections are typically performed by home inspections company's or pest control companies. It is strongly recommended that you have this completed or have the seller provide termite and moisture clearance documents from a qualified company before taking ownership of the property.  Additionally you should have annual inspections for the presence of wood damaging organisms.

Not for 3rd party use - The inspection and report are performed and prepared only for the sole, confidential and exclusive use and possession of the named client(s). Final Analysis Property Inspections accepts no responsibility for use or misrepresentation of this report by third parties who "rely" on the report information but have not directly retained our inspection services and council and are not named in the inspection agreement.

Overview: A thorough home inspection was completed at the subject property in accordance with the American Society Home Inspections (ASHI) standards. The inspection reveals that this dwelling has normal wear and tear.  Its structure and systems are generally well built, sound and maintained in good repair with several major system updates less than 5 years old. All observations made and items reported here should be carefully reviewed and considered for correction where needed as they are specific to this home and can have a significant impact on it's condition, safety and value.

Top Table of Contents Bottom
1.  Roofing
The inspector shall: A. inspect: 1. roofing materials. 2. roof drainage systems. 3. flashing. 4. skylights, chimneys, and roof penetrations. B. describe: 1. roofing materials. 2. methods used to inspect the roofing.

The inspector is NOT required to inspect: A. antennae. B. interiors of vent systems, flues, and chimneys that are not readily accessible. C. other installed accessories.

Styles & Materials
GENERAL ROOF CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Roof service life remaining::
80% - 100% (Very Good - No concerns)
Roof covering material:
Architectural style asphalt shingles
Methods used to inspect the roof:
Walked roof
Attic
Roof drainage system:
No roof drainage systems installed
Attic Ventilation:
Soffit intake vents installed
Thermostatically controlled fan
8x8 static roof outlet vents installed
System items and inspected components.
1.0 ROOF MATERIALS
Comments and observations: Inspected
1.1 FLASHINGS
Comments and observations: Inspected
Disclosure - Roof flashings by design are mostly concealed and therefore inspection is limited to visible areas only followed by examinations and testing of the interiors where leaks are suspected. Some leaks can not be detected and will only show during certain weather conditions.
1.2 SKYLIGHTS, CHIMNEYS and Other ROOF PENETRATIONS
Comments and observations: Inspected
1.3 ROOF DRAINAGE SYSTEMS
Comments and observations: Not Present
1.4 ATTIC VENTILATION
Comments and observations: Inspected
(1) Improper vent configuration - Power fan is installed in close proximity of static outlet vents (Item 1) . The power exhaust fan should pull air up from the soffit intake vents thereby cooling the underside of the roof decking. When installed too close or in tandem with other roof vents the power fan will pull make up air from the closest location and in effect turn the static vents into intake vents thus defeating the purpose of both. 
1.4 (Item 1)
(2) General Statement - Attic ventilation plays an important role in reducing the heat loads in your attic, dissipating trapped moisture and contributing to the overall health of your attic/roof system. A poorly ventilated attic can reduce HVAC performance, shorten shingle life, and will promote rot of wood materials if moisture can't escape. Poor eave/soffit vents are the # reason for poor attic ventilation. Typically newer homes are better ventilated but older homes 20+ years, should be reviewed for improvement. It is important to remember that you need balanced intake vents along with outlet vents for good air flow. Installing just a power fan may not accomplish this. See more ventilation tips here

Attic is ventilated

The roof of this home was inspected and reported on it's current condition with the above information. The roof inspection process and the inspector makes every effort to find all areas of concern in order to provide you with a good general consensus of the roof system's condition. However, this consensus is limited to visual observation only of the overall condition. The roof inspection is not technically exhaustive. Therefore Final Analysis Home Inspections can not and does not claim to find and identify any or all water leaks that exists during the inspection or leak under certain weather conditions or leaks that may occur after the inspection.  Roof construction and flashings are designed as such that many areas are concealed, obstructed, or just not accessible which will allow some problems can to go undetected. The purpose of a roof inspection is to help determine its condition and potential for leaks. We do report obvious leaks or potential problems to support this purpose but the inspection has limitations and should not be construed as all inclusive of all leaks or a guarantee against future leaks. Subjective to the visual finding, we will be able to recommend whether an invasive or technically exhaustive evaluation should be completed by a qualified contractor or specialist. Any repair items mentioned in this report should be considered before purchase. It is further recommended that qualified contractors be used in further evaluating any issues flagged for concern in this report. All repair items requested by you should be subject to your satisfaction and acceptance of the repair entity and their completed workmanship before you go to settlement. Read more about roofing here

~ end of ROOF section ~

Top Table of Contents Bottom
2.  Exterior
The inspector shall: A. inspect: 1. wall coverings, flashing, and trim. 2. exterior doors. 3. attached and adjacent decks, balconies, stoops, steps, porches, and their associated railings. 4. eaves, soffits, and fascias where accessible from the ground level. 5. vegetation, grading, surface drainage, and retaining walls that are likely to adversely affect the building. 6. adjacent and entryway walkways, patios, and driveways. B. describe wall coverings.

 The inspector is NOT required to inspect: A. screening, shutters, awnings, and similar seasonal accessories. B. fences, boundary walls, and similar structures. C. geological and soil conditions. D. recreational facilities. E. outbuildings other than garages and carports. F. seawalls, break-walls, and docks. G. erosion control and earth stabilization measures.

detached garage
view inside garage
Styles & Materials
GENERAL EXTERIOR CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Siding material:
Brick veneer
Trim materials:
Wood
Exterior Entry Doors:
Steel
Fiberglass
Driveway:
Concrete
Evidence of water intrusion at exterior walls windows doors:
No
System items and inspected components.
2.0 Siding, Trim, Eaves, Flashings, Exterior finishes
Comments and observations: Inspected
Observation - Small piece of vinyl missing from gable peak of shed.
2.0 (Item 1)
2.1 Doors (exterior)
Comments and observations: Inspected
(1) Defect -  Observed some exterior trim or jamb rot or deterioration at the garage door frame (Item 1)  and shed door frame. This type of deterioration is common on most home and is typically caused by moisture exposure and delayed maintenance but can be costly to repair especially if the door frame has to be replaced. Recommend further evaluation, repairs and cost estimates be obtained from a qualified repair contractor.
2.1 (Item 1)
2.1 (Item 2)
(2) Defect - Poor weather seal observed at front entry door. (Item 3) The threshold seal is missing and the frame seals are leaking air. Recommend correction for weather tightness.
2.1 (Item 3)
2.2 Windows (exterior)
Comments and observations: Inspected
2.3 Decks, Balconies, Stoops, Steps, Porches, Patio/Sun rooms, Railings
Comments and observations: Inspected
SAFETY - Handrails missing at front steps and side steps. (Items 1- 2) This information is provided for your safety.
2.3 (Item 1)
2.3 (Item 2)
2.4 Vegetation, Grading, Drainage, Driveways, Walkways, Retaining walls (With respect to their effect on the condition of the building)
Comments and observations: Inspected
General Information - Positive grading and drainage are essential to the welfare of a property, and are usually the primary concern of architects and builders. Moisture can deteriorate most surfaces, cause soil movement and erosion, and undermine the structures foundation. The ideal site will be graded to conduct water away from a building. In fact, the ideal building will be surrounded by hard surfaces that slope way from the exterior walls, the interior floors will be several inches higher than the exterior grade, and the building will have gutters and downspouts and a system of drainage designed to prevent any moisture from threatening the foundation or the living space. Unfortunately, many properties do not meet this ideal, conditions on most can generally be improved, and all need to be monitored and maintained to prevent damage. Also, inspectors cannot see inside area drains and do not water-test them, but they can become blocked by debris, occluded by silt, and damaged by movement. Therefore, buyers should question sellers about the functionality of any such system, have it serviced by a specialist, or assume the risk of having a system that does not function well and the damage that might result
2.5 Garage, Garage door, opener safety reverse (if applicable)
Comments and observations: Inspected
Defect, Safety - The garage overhead door is unbalanced. (Item 1) The garage door should stay in place at any location in it's travel. It should not fly open or drop shut. An unbalanced garage door can cause personal injury and can cause stress damage to the door system. Recommend professional repairs be completed by a qualified garage door technician.
2.5 (Item 1)
The exterior of the home was inspected and reported on with the above information. While the inspector makes every effort to find all areas of concern, some areas can go unnoticed. Please be aware that the inspector has your best interest in mind. Any repair items mentioned in this report should be considered before purchase. It is recommended that qualified contractors be used in your further inspection or repair issues as it relates to the comments in this inspection report.
Top Table of Contents Bottom
3.  Interiors
The inspector shall observe: Walls, ceiling, and floors; Steps, stairways, balconies, and railings; Counters and a representative number of installed cabinets; and A representative number of doors and windows. The inspector shall: Operate a representative number of windows and interior doors; and Report signs of abnormal or harmful water penetration into the building or signs of abnormal or harmful condensation on building components. The inspector is not required to observe: Paint, wallpaper, and other finish treatments on the interior walls, ceilings, and floors; Carpeting; or Draperies, blinds, or other window treatments.

This inspection does not test for or report on the presence of MOLD or other indoor air quality issues or hazards.

laundry room
Main bathroom
1st bedroom
corner bedroom
master bedroom
master bath
Styles & Materials
GENERAL INTERIOR CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Ceiling construction materials:
Drywall, Sheet rock, Gypsum
Wall constructuion material:
Gypsum board (typical)
Floor Covering(s):
Hardwood T&G
Ceramic or porcelain tile
Window Types:
Vinyl or Plastic
Double-hung
Thermal/Insulated
Interior Doors / types / styles:
Hollow core
Masonite
Cabinetry:
Wood
Countertop:
Laminate
 
System items and inspected components.
3.0 CEILINGS
Comments and observations: Inspected
3.1 WALLS
Comments and observations: Inspected
3.2 FLOORS
Comments and observations: Inspected
3.3 STEPS, STAIRWAYS, BALCONIES AND RAILINGS
Comments and observations: Not Present
3.4 COUNTERS AND A REPRESENTATIVE NUMBER OF CABINETS
Comments and observations: Inspected
3.5 DOORS (REPRESENTATIVE NUMBER)
Comments and observations: Inspected
3.6 WINDOWS (REPRESENTATIVE NUMBER)
Comments and observations: Inspected
Replacement vinyl thermal tilt windows 2011 (Item 1)
3.6 (Item 1)
The interior of the home was inspected and reported on with the above information. While the inspector makes every effort to find all areas of concern, some areas can go unnoticed or are not accessible. Inside wall framing and cavities are not inspected but may contain concealed or hidden damages such as rot, termites, rodent nesting, missing insulation or leaky plumbing. This inspection does not report obvious cosmetic or esthetic conditions such as aging,  wear and tear, dirt  filth, soil or physical damage to walls, ceilings, floors, cabinets and counters. . The inspection did not involve moving furniture and inspecting behind furniture, area rugs or areas obstructed from view. Any repair items mentioned in this report should be considered and resolved before closing of purchase. It is recommended that qualified contractors be used in your further inspection or repair issues as it relates to the comments in this inspection report.
Top Table of Contents Bottom
4.  Structural Components
The inspector shall: A. Inspect structural components including the foundation and framing. B. describe: 1. the methods used to inspect under-floor crawlspaces and attics. 2. the foundation. 3. the floor structure. 4. the wall structure. 5. the ceiling structure. 6. the roof structure. The inspector is NOT required to: A. provide engineering or architectural services or analysis. B. offer an opinion about the adequacy of structural systems and components. C. Enter under-floor crawlspace areas that have less than 24 inches of vertical clearance between components and the ground or that have an access opening smaller than 16 inches by 24 inches. D. traverse attic load-bearing components that are concealed by insulation or by other materials.
representative view of crawpslace
crawlspace underneath enclosed garage
representative view of crawlspace
Styles & Materials
GENERAL STRUCTURAL CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Attic access:
Ceiling scuttle hole
Method used to observe attic:
From entry
Crawl space access point:
Exterior
Metal
Method used to observe Crawlspace:
Crawled
Is there significant structural faiulre/damage/distress was observed/suspected:
NO
Was there evidence of Harmful Moisture / Water Conditions at foundation/crawlspace:
No
Was there evidence of Harmful Moisture Conditions in Attic:
No
Crawlspace ventilation:
foundation vents
Adequate
Foundation type:
Crawlspace
Floor Structure:
Conventional wood framed
Wall Structure:
Conventional wood frame
Columns or Piers:
Masonry block
Ceiling Structure:
Conventional wood frame
Roof Structure:
Stick-built
2 X 6 Rafters
Plywood
Sheathing
Roof-Type:
Hip
   
System items and inspected components.
4.0 FOUNDATIONS, SLABS AND CRAWLSPACES (Report signs of abnormal or harmful water penetration into the building or signs of abnormal or harmful condensation on building components. Fungus or wood destroying insects)
Comments and observations: Inspected
(1) Slab / Foundation block is even or below grade level and vulnerable to moisture intrusion and rot damage to wall framing along sill plate at detached garage. (Items 1 and 2)  These areas should be cleared away and inspected for damage. Improvements such as proper grading, drainage and foundation water proofing is also recommended to be completed by a qualified person or contractor experienced in correcting these conditions.
4.0 (Item 1)
4.0 (Item 2)
(2) Deficiency - Observed water intrusion via capillary movement at the sill plate of enclosed garage door opening. (Items 3- 4)  No damage was detected at this point. Monitor for future problems.
4.0 (Item 3)
4.0 (Item 4)
(3) Observation - There is evidence of vermin or rodent nesting/infestation in the attic. Observed feces, nesting materials and insulation tunneling . It is not unusual to see some level of vermin in these spaces of many homes. Vermin can do significant damage to wiring, insulation and building materials and can block critical ductwork such as dryer, stove and bathroom vents. Typical suspects are rodents, birds and squirrels. Feces and carcasses can present a health hazard. It is recommended that you have all holes and entry points blocked or sealed.  Pest control operators and exterminators are the professionals that do this kind of work.
4.0 (Item 5)
4.1 VAPOR RETARDERS (Crawl pace)
Comments and observations: Inspected
4.2 STRUCTURAL FRAMING walls, floors, ceilings (where visible)
Comments and observations: Inspected
No structural framing distress or failure was visibly detected.
4.3 STRUCTURAL MASONRY, COLUMNS, PIERS, CONCRETE SLAB
Comments and observations: Inspected
4.4 ROOF STRUCTURE AND ATTIC
Comments and observations: Inspected
4.5 CRAWL SPACE VENTILATION (if applicable)
Comments and observations: Inspected
4.6 RETAINER WALLS
Comments and observations: Inspected
The structure of the home was inspected and reported on with the above information. We have made every reasonable effort within the confines of a limited visual inspection to discover and report obvious or suspected deficiencies. We attempted to discover and report all structural defects and deficiencies but the primary focus is on significant structural concerns which takes precedence over smaller discrepancies.  Hidden, Concealed or buried components of the structural system such as foundation footings, pier depth, fireplace foundations, etc that are below grade are not inspected.

Additionally, due to the nature of a home inspection being a visual, non-invasive examination of readily accessible areas, some deficiencies, even significant ones can go unnoticed due to limited visibility, concealment, or other restriction. Any system restrictions that limit us from reporting on any major components will be flagged and identified in this report.

Finally discrepant or deficient items identified in this report should be carefully reviewed and considered while releasing any inspection contingency you may have in a purchase contract. Furthermore, items reported as deficient or questionable should be further evaluated and properly corrected as needed and determined by qualified persons. Some of these persons may need to be licensed, certified professionals or experts in their field or industry.  All work or repairs should meet or exceed minimum workmanship and typically accepted industry quality standards and should be subject to your approval, satisfaction and final acceptance. 

Top Table of Contents Bottom
5.  Plumbing System
The inspector shall: A. inspect: 1. interior water supply and distribution systems including fixtures and faucets. 2. interior drain, waste, and vent systems including fixtures. 3. water heating equipment and hot water supply systems. 4. vent systems, flues, and chimneys. 5. fuel storage and fuel distribution systems. 6. sewage ejectors, sump pumps, and related piping. B. The inspector shall describe: 1. interior water supply, drain, waste, and vent piping materials. 2. water heating equipment including energy source(s). 3. location of main water and fuel shut-off valves. 6.2 The inspector is NOT required to: A. inspect: 1. clothes washing machine connections. 2. interiors of vent systems, flues, and chimneys that are not readily accessible. 3. wells, well pumps, and water storage related equipment. 4. water conditioning systems. 5. solar, geothermal, and other renewable energy water heating systems. 6. manual and automatic fire extinguishing and sprinkler systems and landscape irrigation systems. 7. septic and other sewage disposal systems. B. determine: 1. whether water supply and sewage disposal are public or private. 2. water quality. 3. the adequacy of combustion air components.C. measure water supply flow and pressure, and well water quantity. D. fill shower pans and fixtures to test for leaks.
Styles & Materials
GENERAL PLUMBING SYSTEM CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Water heater service life remaining:
Unknown, Data Illegible
Probability of plumbing leaks:
Low
Domestic Potable Water Source (not yard irrigation):
Public (municiple)
Plumbing waste system:
City sewage
Water Supply pipe (from street meter):
Copper
Water Distribution pipes (inside structure - visible areas only):
Copper
Plumbing Waste / Drain pipe materials:
Galvanized (antiquated, Limited service life)
Cast iron (antiquated)
AGED
Domestic hot water source:
Electric storage tank
in laundry room
Water Heater Capacity:
Unknown, data not available
Hot water temperature:
110-120 deg F. (low)
Main water shut off location:
Primary valve is at the municipal water meter location
Secondary water shut off is in the front flower bed
System items and inspected components.
5.0 PLUMBING DRAIN, WASTE AND VENT SYSTEMS
Comments and observations: Inspected
DISCLOSURE: This home contains antiquated style galvanized steel and/or cast iron drains which is typical for the age of construction. (Item 1) However, as these pipes age, they have a tendency to constrict, drain slowly and back-up do to internal rusting and corrosion. These pipes also corrode from the inside-out. They can look good from the exterior but may have internal damage.  Vertical cast iron waste pipes are that are concealed inside the walls are subject to stress cracks and may leak internally with no detection. Most pipes are hidden inside the walls or floors and can cause water damages that can go unnoticed for a long time. These older style pipes have a high probability of failure. Pipes that are inside the walls or buried in the earth, underneath vapor barrier, behind insulation can not be inspected. An internal video scope inspection or pressure testing is beyond the scope of a home inspection but can be completed by a plumber to determine the pipes internal condition. Some pipes can be reamed out a few times to restore adequate drainage but this is temporary and eventually the pipes will have to be replaced.  These type of drains have a limited service life of approx 30 - 50 years. Leaks, failure and the need for replacement is inevitable and costly so this should be considered when buying a house. Replacing these type pipes in homes that are built on concrete slabs can be very expensive because it involved removal of flooring and concrete. Home with crawlspaces are usually accessible and much easier to replace. This home is on a crawlspace  If you are concerned about these pipes you should have them further evaluated and cost estimates obtained from a licensed, qualified plumber.
5.0 (Item 1)
5.1 PLUMBING WATER SUPPLY AND DISTRIBUTION SYSTEMS AND FIXTURES
Comments and observations: Inspected
(1) Defect - Drain is slow or backing up in the hall bath tub (Item 1) . Generally speaking, a fixture should drain at least as quick as it fills to prevent overflow. Drain restrictions can be a simple trap clog or something more serious which can not be determined by inspection alone. Recommend further evaluation and correction be completed by a qualified individual or contractor.
5.1 (Item 1)
(2) Defect - Toilet is loose at floor mounts and drain flange in master bath and is subject to leaking at base (Item 2) . Repairs may involve re-setting the toilet on a new wax seal. Water can leak into the flooring and cause damage that is not detectable at first. Recommend a qualified licensed plumber repair or correct as needed.
5.1 (Item 2)
5.2 HOT WATER SYSTEMS
Comments and observations: Inspected
(1) General safety information about hot water temperatures - Hot water systems can be a scald hazard and a source of disease. Water temperatures higher than 130 deg F. can be a scald hazard. Water temperatures less than 120 deg. F. is considered ideal for the growth of harmful bacteria inside the tank–such as Legionella.  Monitor your hot water temperatures for safety.

Information sources:

http://EPA/Legionella: Drinking Water Health Advisory

https://OSHA/Domestic Hot Water Systems

http;//CSPC avoiding hot water scalds

5.2 (Item 1)
(2) Observation - the water heater appears newer and is functional but all data has been removed. This is typically done to void warranties on "scratch and dent" sales.
5.2 (Item 2)
5.2 (Item 3)
5.3 FUEL STORAGE AND DISTRIBUTION SYSTEMS (Interior fuel storage, piping, venting, supports, leaks)
Comments and observations: Not Present
5.4 MAIN FUEL SHUT OFF (Describe Location)
Comments and observations: Not Present
5.5 SUMP PUMP, LIFT PUMPS, GRINDERS
Comments and observations: Not Present
The plumbing in the home was inspected and reported on with the above information. The inspector makes every effort to find all areas of concern and we will report all obvious defects or deficiencies. However, the plumbing systems inspection is based on visual observation only and the objective is to determine it's general, overall condition and potential for failure and whether you should have further evaluated by a plumbing contractor using specialized equipment. This plumbing inspection is not  technically exhaustive and some areas cannot be inspected which may permit some defects to go undetected.  Washing machine drain pipes for example cannot be checked for leaks or the ability to handle the volume during drain cycle. Older homes with galvanized supply lines or cast iron drain lines can be obstructed but still draining satisfactory during an inspection but then fails under normal everyday use. Buried pipe or the internal condition of pipes is not visible and not inspected. If the water is turned off or not used for periods of time (like a vacant home waiting for closing) rust or deposits within the pipes can further clog the piping system. Any repair items mentioned in this report should be considered before purchase and work should be done only by a qualified licensed plumber or plumbing contractor who can further evaluate and correct the issues as they relate to the comments in this report. All repairs should adhere to all local municipal permit and inspection requirements by the city.  Any work requested prior to closing of escrow (settlement) should have receipts/work orders provided by the contractor and all work should be subject to your re-inspection, satisfaction, and acceptance.

  Info Link  Guide to Hot Water Heater Selection, Inspection, Diagnosis, & Repair.

Top Table of Contents Bottom
6.  Electrical System
The inspector shall inspect: 1. service drop. 2. service entrance conductors, cables, and raceways. 3. service equipment and main disconnects. 4. service grounding. 5. interior components  of service panels and subpanels. 6. conductors. 7. overcurrent protection devices. 8.   a representative number of installed lighting fixtures, switches, and receptacles. 9. ground fault circuit interrupters and arc fault circuit interrupters.

The Inspectors shall describe: 1. amperage rating of the service. 2. location of main disconnect(s) and subpanels. 3. Thee presence or absence of smoke alarms and carbon monoxide alarms. 4. the predominant branch circuit wiring method.

The inspector is NOT required to inspect: 1. remote control devices. 2. or test smoke and carbon monoxide alarms, security systems , and other signaling and warning devices. 3. low voltage wiring systems  and components. 4. Ancillary wiring systems  and components  not a part of the primary electrical power distribution system. 5. Solar, geothermal, wind, and other renewable energy systems. B. measure amperage, voltage, and impedance. C. Determine the age and type of smoke alarms and carbon monoxide alarms.

Styles & Materials
GENERAL ELECTRICAL CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Electrical inspection limitations:
None, Inspected in accordance with ASHI standards of practice.
Electrical Service Cable (from utility pole or transformer):
Overhead service
Aluminum
4/0 cable
Location of MAIN electric service panel(s):
utility/laundry room
Electric service and panel(s):
200 AMP
Adequate capacity
Main breaker
Circuit breakers
Branch circuit wiring/distribution for 15 and 20 AMP lighting and outlets:
Solid Copper
Romex - NM plastic (normal - typical)
Grounded (3 prong outlets)
"wet area" outlets pre-date GFCI requirments. Recommend update for safety
SMOKE DETECTORS:
Yes
Recommend updating for safety
Some Do Not respond
CARBON MONOXIDE DETECTORS:
No
 
System items and inspected components.
6.0 SERVICE ENTRANCE CONDUCTORS
Comments and observations: Inspected
(1) Safety information - This home has on older style overhead electric service feed wire which is typical for the age. Use extreme caution when working with large trucks, ladders and equipment.
6.0 (Item 1)
(2) Defect - observed the tree limbs that are in contact with electric service wiring  which can cause damage. (Item 2)  These limbs should be trimmed away so they are not close to, or contacting the service wires.
6.0 (Item 2)
6.1 SERVICE AND GROUNDING EQUIPMENT, MAIN OVERCURRENT DEVICE, MAIN AND DISTRIBUTION PANELS
Comments and observations: Inspected
6.2 BRANCH CIRCUIT CONDUCTORS, OVERCURRENT DEVICES AND COMPATIBILITY OF THEIR AMPERAGE AND VOLTAGE
Comments and observations: Inspected
6.3 CONNECTED DEVICES AND FIXTURES (Observed from a representative number operation of ceiling fans, lighting fixtures, switches and receptacles located inside the house, garage, and on the dwelling's exterior walls)
Comments and observations: Inspected
(1) SAFETY - There are one or more switch covers missing from electrical outlets and wall switches. Covers reduce the risk of fire and shock. Install all outlet and switch covers where needed.
6.3 (Item 1) master bedroom
6.3 (Item 2) master bathroom
6.3 (Item 3) detached garage
6.3 (Item 4)
(2) Defect - Amateur light switch installation observed in the hallway. The hallway has a 2 way switch installed on a 3 way circuit which means that when the light switch is in the off position, the 2nd switch will not respond and vice versa. (Item 1) Recommend professional repairs be completed by a qualified electrical contractor.
6.3 (Item 5)
(3) Safety -  Observed some exposed Romex wiring in garage which is the shed feed wire (Item 5)  Wiring in exposed walls must be covered for safety or inside a conduit.
6.3 (Item 6)
(4) Defect, safety - Electric junction box cover is missing in attic (Item 6)  near opening and electrical connections are exposed which could result in shock or electrocution. Recommend professional repairs be completed by an electrician for safety.
6.3 (Item 7)
(5) Defect, Safety - Exposed wiring observed at exterior light switch of shed. (Item 8)  Recommend professional electrical repairs.
6.3 (Item 8)
(6) Defect - Electrical conduit pull box is loose, detached and may be an electrical hazard. (Item 9)  Recommend professional electrical repairs. 
6.3 (Item 9)
6.4 POLARITY AND GROUNDING OF ELECTRIC RECEPTACLES
Comments and observations: Inspected
Defect, Safety -  An "open ground" reading was detected at the hall bath wall outlet (Item 1). Open grounds are caused by an opening in the ground circuit somewhere between the affected outlet and the main electric service panel. Typically it's a loose wire on the outlets ground terminal, but it can be anywhere in the circuit such as an upstream outlet that feeds this outlet. The ground circuit is designed to divert dangerous electricity away from your body and prevent electrocution. Ungrounded outlets are unsafe and can cause injury or death. It is recommended that this condition be further evaluated and corrected by a qualified electrician.
6.4 (Item 1)
6.4 (Item 2)
6.5 OPERATION OF GFCI (GROUND FAULT CIRCUIT INTERRUPTERS)
Comments and observations: Inspected
Information/Disclosure -  No Ground Fault Circuit Interrupts , SAFETY - This home was built before GFCI technology was required in certain circuits and therefore is missing some or all GFCI protection in "wet area" outlets such as; bathrooms, kitchen, exterior, garage, etc. (Items 1- 3)  GFCI's protect against shocks and electrocution.  Recommend consider upgrading to modern GFCI's. GFCI's save lives!.
6.5 (Item 1)
6.5 (Item 2)
6.5 (Item 3)
6.5 (Item 4)
6.6 OPERATION OF AFCI (ARCH FAULT CIRCUIT INTERRUPTERS)
Comments and observations: Inspected
Information/Disclosure - Non Arch Fault Circuit Interrupts , SAFETY - This home was built before AFCI technology and therefore is missing some or all AFCI protection in bedrooms. AFCI's protect against shorts, sparking and fires.. Recommend consider upgrading to AFCI protection.

“Older homes are statistically more vulnerable to electrical fires. Extra protection for older homes is provided by the gradual replacement, over time, of non-AFCI-protected receptacles with new AFCI-protected ones.” The NEC

AFCI's prevent fires.  Click here for more information on AFCI's

6.7 SMOKE and CARBON MONOXIDE DETECTORS
Comments and observations: Inspected
Safety, Repair - One or more installed smoke detectors failed to respond to test. (Items 1 and 2)  Have repaired or replaced as needed by a professional. Test again during final walk-thru inspection then continue to test monthly. Note: these are battery operated only. Properly working smoke detectors save lives.
6.7 (Item 1) first bedroom on right
6.7 (Item 2)
The electrical system of the home was inspected and reported on with the above information. While the inspector makes every effort to find all areas of concern, some areas can go unnoticed. Outlets were not removed and the inspection was only visual. Any outlet not accessible (behind the refrigerator or furniture for example) was not inspected or accessible. Electric issues or defects can be a fire or safety hazard and all reported electrical concerns should be considered for repair only by a qualified licensed electrician or electrical contractor who can further evaluate and correct the issues as they relate to the comments in this report. All repairs should adhere to all local municipal permit and inspection requirements by the city. Any work requested prior to closing of escrow (settlement) should have receipts/work orders provided by the contractor and all work should be subject to your re-inspection, satisfaction, and acceptance.
Top Table of Contents Bottom
7.  Heating / Central Air Conditioning
HEATING -The inspector shall: A. open readily openable access panels.B. inspect: 1. installed heating equipment. 2. vent systems, flues, and chimneys. 3. distribution systems. C. describe: 1. energy source(s). 2. heating systems.  The inspector is NOT required to: A. inspect: 1. interiors of vent systems, flues, and chimneys that are not readily accessible. 2. heat exchangers. 3. humidifiers and dehumidifiers. 4. electric air cleaning and sanitizing devices. 5. heating systems using ground-source, water-source, solar, and renewable energy technologies. 6. heat-recovery and similar whole-house mechanical ventilation systems. B. determine: 1. heat supply adequacy and distribution balance. 2. the adequacy of combustion air components.

AC - The inspector shall: A. open readily openable access panels. B. inspect: 1. central and permanently installed cooling equipment. 2. distribution systems. C. describe: 1. energy source(s). 2. cooling systems.9.2 The inspector is NOT required to: A. inspect electric air cleaning and sanitizing devices. B. determine cooling supply adequacy and distribution balance. C. inspect cooling units that are not permanently installed or that are installed in windows. D. inspect cooling systems using ground-source, water-source, solar, and renewable energy technologies.

FIREPLACES AND FUEL-BURNING APPLIANCES - The inspector shall: A. inspect: 1. fuel-burning fireplaces, stoves, and fireplace inserts. 2. fuel-burning accessories installed in fireplaces. 3. chimneys and vent systems.B. describe systems and components listed in 12.1.A.1 and .2.  The inspector is NOT required to: A. inspect: 1. interiors of vent systems, flues, and chimneys that are not readily accessible. 2. fire screens and doors. 3. seals and gaskets. 4. automatic fuel feed devices. 5. mantles and fireplace surrounds. 6. combustion air components and to determine their adequacy. 7. heat distribution assists (gravity fed and fan assisted). 8. fuel-burning fireplaces and appliances located outside the inspected structures. B. determine draft characteristics. C. move fireplace inserts and stoves or firebox contents.

Styles & Materials
Heat Type:
Heat Pump Forced Air (also provides cool air for AC)
GENERAL AC/ HP SYSTEM CONDITION / RATING:
Good (No significant concerns, functioning as designed)
HEAT PUMP / AC - SERVICE LIFE REMAINING::
50% - 80% (Good - No concerns outside of normal maintenance)
Cooling Equipment Type:
Heat Pump Forced Air (also provides warm air, Heat)
AC/Heat Pump system(s) performance:
Satisfactory
AC/Heat Pump system(s) capacity:
Satisfactory
Number of Central AC / HP systems:
One
Number of conditioned zones in the house/building:
1
Ductwork:
insulated flex duct
Filter Type:
Disposable
Types of Fireplaces:
None
 
System items and inspected components.
7.0 AC COOLING, HEAT PUMP AND AIR HANDLER EQUIPMENT
Comments and observations: Inspected
(1) Heat Pump equipment performance - The ambient air test was performed by using thermometers on the air handler of Heat pump in cool mode to determine if the difference in temperatures of the supply and return air are between 14 degrees and 22 degrees which indicates that the unit is cooling as intended. The supply air temperature on your system read 46 degrees (Item 1) , and the return air temperature was 67 degrees (Item 2) . D/T = 21 deg. F.  This indicates satisfactory performance and the system is functioning as designed..

Emergency heat is functional. (Item 3)

7.0 (Item 1)
7.0 (Item 2)
7.0 (Item 3)
(2) This home is primarily heated and cooled with heat pump system(s). It is the same system and equipment that provides warm air in the winter and cool air in the summer.  When the outside temperature is below 60 deg. F. the system is tested in "heat" mode, When the outside temperature is above 60 deg.F. it is tested in the "cool" mode. Heat pumps can only be tested in Heat or Cool but not both.

Most heat pump systems contain auxiliary (emergency, back-up) heat, typically electric coils but can be gas or oil.  This is always tested winter or summer for response. However, some electronic thermostats when in "cool" mode will not allow manual switching to axillary heat, in which case it can not be tested.

(3) Defect - Some of the electric baseboard heaters do not respond to thermostat.
7.0 (Item 4)
7.0 (Item 5)
7.1 PRESENCE OF INSTALLED AC/HP SOURCE AIR IN EACH ROOM
Comments and observations: Inspected
7.2 NORMAL OPERATING CONTROLS
Comments and observations: Inspected
7.3 DISTRIBUTION SYSTEMS (including fans, pumps, ducts and piping, with supports, insulation, air filters, registers, radiators, fan coil units and convectors)
Comments and observations: Inspected
7.4 CHIMNEYS, FLUES AND VENTS (for fireplaces, water heaters or heat systems)
Comments and observations: Not Present
7.5 SOLID FUEL HEATING DEVICES (Fireplaces, Woodstove)
Comments and observations: Not Present
7.6 GAS/LP FIRELOGS AND FIREPLACES
Comments and observations: Not Present
The heating and cooling systems of this home was inspected and reported on with the above information.The inspector makes every effort to find all areas of concern regarding safety, performance and potential repairs expense. However, HVAC systems can be complex in design and some aspects of these systems are concealed or limited during a visual exam and functional testing. It is beyond the scope of a home inspection to do technically exhaustive evaluations, trouble shooting or diagnostics on Heat and AC systems but we make every effort to determine and recommend an HVAC expert whenever there appears top be obvious or latent problems with the systems.  The inspection does not involve removal and internal component inspection, behind service doors or dismantling that would otherwise reveal something only a licensed HVAC contractor would discover. Any repair items mentioned in this report should be considered before purchase. Where corrections are deemed necessary or recommended in this report, It is always crucially important  that qualified, experienced HVAC contractors be used to further evaluate and prescribe appropriate repairs, replacement and testing of your HVAC systems in a manner that will ensure safe, proper, function as intended and designed. All work completed by contractors should accompany receipts/work orders and any required municipal permits and city inspections and the completed work should be subject to your re-inspection, satisfaction and acceptance before the work is paid for or before you take possession of the property.

Flue pipe and combustion chamber inspections are beyond the scope of this inspection. The internal areas of a flue pipe, metal chimney, masonry chimney, fireplace or otherwise are not accessible for visual examination and in most cases can not be evaluated without the use of special equipment such as an internal camera or video scope. Furthermore, If a flue has soot or creosote build-up, it has to be professionally cleaned before an inspection can be completed. Any observations or comments reported in this regard are intended for guidance only and are inconclusive and should not be construed as a substitute for a full and proper inspection. It is highly recommended that your have all chimneys and flues inspected by qualified contractors. Chimney damage can represent significant repair cost and can also present a fire hazard.

Top Table of Contents Bottom
8.  Insulation and Ventilation
The inspector shall observe: Insulation and vapor retarders in unfinished spaces; Ventilation of attics and foundation areas; Kitchen, bathroom, and laundry venting systems; and the operation of any readily accessible attic ventilation fan, and, when temperature permits, the operation of any readily accessible thermostatic control. The inspector shall describe: Insulation in unfinished spaces; and Absence of insulation in unfinished space at conditioned surfaces. The inspector shall: Move insulation where readily visible evidence indicates the need to do so; and Move insulation where chimneys penetrate roofs, where plumbing drain/waste pipes penetrate floors, adjacent to earth filled stoops or porches, and at exterior doors. The inspector is not required to report on: Concealed insulation and vapor retarders; or Venting equipment that is integral with household appliances.
Styles & Materials
GENERAL INSULATION CONDITION / RATING:
Good (No significant concerns, functioning as designed)
Attic insulation:
Improvements recommended
Loose or blown in
fiberglass
Approx. R-11
poor
Wall insulation:
concealed, not visible, not inspected
Floor System Insulation:
Faced
Batts
Fiberglass
loose, tattered, fallen
R-11
Bathroom steam vents:
Fan only
Dryer Power Source:
220 Electric
Dryer duct (built in):
Metal
   
System items and inspected components.
8.0 INSULATION IN ATTIC / CEILING
Comments and observations: Inspected
Attic insulation thickness is marginal or substandard but may have met typical requirements for the age of construction or it could have settled or become packed down with storage. (Items 1- 2)  It does not meet the current standards or R factor of 38 which is recommended by the Department of Energy. The attic or ceilings is where you'll loose (or gain) the most amount of heat transfer. Consideration should be given to upgrading. It is cost effective and will increase the thermal efficiency of your home.

Visit these links and learn more about your homes insulation:

See US Dept of Energy insulation consumer guide | See Insulation fact Sheet. | See Insulation calculator and estimators | Dept of Energy insulation zone map

8.0 (Item 1)
8.0 (Item 2)
8.1 WALL INSULATION (if visible)
Comments and observations: Not Inspected
8.2 INSULATION UNDER FLOOR SYSTEM
Comments and observations: Inspected
Defect - Floor insulation batts are loose or fallen in multiple locations of the crawlspace. Repair or replace as needed.
8.2 (Item 1)
8.2 (Item 2)
8.2 (Item 3)
8.3 VENTING SYSTEMS (Kitchens, baths and laundry)
Comments and observations: Inspected
SAFETY ADVISORY- Dryer ducts should be cleaned and inspected annually for proper performance. Dryer ducts are susceptible to clogging and blockage due to lint and moisture build up. Restricted dryer vents will not only reduce drying efficiency, but worse they can overheat and cause fires.

If your dryer used a vinyl or foil flex duct connector you should dispose of it and replace with flexible aluminum duct. Aluminum duct is the most efficient type, safest type to reduce fire hazards and the only type recommended by dryer manufactures and by most municipal building codes.

Dryer vent installation guidelines   See more about dryer duct safety here.

Video Proper installation of a dryer and vent

The insulation and ventilation of the home was inspected and reported on with the above information. While the inspector makes every effort to find all areas of concern, some areas can go unnoticed. Venting of exhaust fans or clothes dryer cannot be fully inspected and bends or obstructions can occur without being accessible or visible (behind wall and ceiling coverings). Only insulation that is visible was inspected. Please be aware that the inspector has your best interest in mind. Any repair items mentioned in this report should be considered before purchase. It is recommended that qualified contractors be used in your further inspection or repair issues as it relates to the comments in this inspection report.

Visit these links and learn more about your homes insulation:

See US Dept of Energy insulation consumer guide | See Insulation fact Sheet. | See Insulation calculator and estimators | Dept. of Energy insulation zone map.

Top Table of Contents Bottom
9.  Built-In Kitchen Appliances
The inspector shall observe and operate the basic functions of the following kitchen appliances: Permanently installed dishwasher, through its normal cycle; Range, cook top, and permanently installed oven; Trash compactor; Garbage disposal; Ventilation equipment or range hood; and Permanently installed microwave oven. The inspector is not required to observe: Clocks, timers, self-cleaning oven function, or thermostats for calibration or automatic operation; Non built-in appliances; or Refrigeration units including refrigerators and freezers. The inspector is not required to operate: Appliances in use; or Any appliance that is shut down or otherwise inoperable.
Styles & Materials
GENERAL APPLIANCE CONDITION / RATING:
Good (No significant concerns, functioning as designed)
GARBAGE DISPOSAL:
None installed
DISHWASHER:
Functional
Aging
RANGE/OVEN/STOVE/COOK TOP:
Functional
Aging
MICROWAVE OVEN (built in):
None installed
STOVE EXHAUST / RANGE HOOD:
Functional
Aging
System items and inspected components.
9.0 DISHWASHER
Comments and observations: Inspected
9.1 RANGES/OVENS/COOKTOPS
Comments and observations: Inspected
Safety disclosure - The oven/range does not contain an anti-tip bracket and is subject to tipping when the door is opened and weight is placed on the door. (Item 1) According to the US CPSC (US Consumer Product Safety Commission) stoves without an anti-tip bracket or device can cause injury or death, especially to small children. Since 1991 it has been required that all electric and gas ranges have an anti-tip device installed when the oven/range is installed.  This information is provided for your safety.
9.1 (Item 1)
9.1 (Item 2)
9.1 (Item 3)
9.2 RANGE HOOD
Comments and observations: Inspected
9.3 GARBAGE DISPOSAL UNIT
Comments and observations: Not Present
9.4 MICROWAVE COOKING EQUIPMENT
Comments and observations: Not Present
Appliance inspection is limited - The built-in appliances of the home were inspected and reported on with the above information. Appliances are inspected for functional response only to determine whether they work or not. Condition and performance is not evaluated or commented on unless it effects the operation of the appliance during the inspection.  Refrigerators and ice makers, Freezers, Washers, Dryers and other non "built-in" appliances are personal property, not covered under this inspection and if they convey with the sale it's typically "as is". You may want to consider obtaining a whole house warranty for added protection.
Top Table of Contents Bottom